This was performed by our friends from DCC Xpress installations.
They offer high quality WOWSound installations for a flat rate complete with free return shipping!
You can find them at: www.dxinstalls.com

This installation is for a HO-Scale Walthers EMD SD45 using a TCS WOW121-Diesel Decoder, AS-MB2 NC Motherboard, KA4 Keep Alive®
and UNIV-SH1-C WOWSpeaker kit.

This was performed by our friends from DCC Xpress installations.
They offer high quality WOWSound installations for a flat rate complete with free return shipping!
You can find them at: www.dxinstalls.com


These items are available in the WDK-KAT-3 which was used for this installation.
AS-MB2-NC Motherboard WOW121-Diesel Decoder UNIV-SH1-C Speaker Kit KA4 Keep-Alive™
Click here for more information on the WDK-KAT-3 and the rest of the WOWDiesel Kits line.

 

HO Scale Walthers SD45 shown prior to installation.

    

 To start off this install, we must first remove the front and rear coupler screws highlighted above and their housings.

With the couplers removed, while gently pulling outwards at each end and along each side of the frame, lift the shell off of the frame.
Take care to release the handrails as you lift off the shell so they don't break.

    

With the couplers removed, also remove the two screws under the frame as highlighted above in red.

Walthers SD45 with the shell off. Remove the 4 screws highlighted above in red along with the wires from the original lighting board and remove it from the chassis.

With the original lighting board removed, trim, tin or lengthen the wires as necessary. Using small lengths of TCS 3/32" and 3/64" shrink tubing, insulate these solder leads.

Using double sided foam tape, attach the AS-MB2 NC to the frame and solder the motor and track pickup wires according to the included wiring diagram.

With the 35mm X 16mm WOWSound speaker inserted into the UNIV-SH1-C enclosure and using double sided foam tape, mount this assembly to the frame as shown.

If your speaker enclosure installation covers the portholes on the enclosure, we recommend adding new port hole(s) similar to the original porting. Be sure that the new portholes are the same size and amount of the original and are vented freely into the locomotive We have found introducing a port of the correct size greatly increases the volume and sound quality of the installation. Too much or too little porting decreases the sound quality.

 

Replace the lighting into it's original positions and solder these wire leads to the motherboard according to the included wiring diagram.

TCS motherboards include on board current limit resistors for LED use. There is no need to apply external resistors for LED use. 

Using the same double sided foam tape, secure the KA4 Keep AliveĀ® to the frame as shown above. Solder these wire leads to the motherboard.

The installation shown complete. We used TCS 1/4" and 3/4" Kapton tape tp secure the wire leads to prevent movement and potential shorts.

You can now plug in your WOW121 decoder.

Lastly, in order to keep the wires neat and prevent possible shorts, lace the wires into a bundle using lacing cord, which is a wax impregnated string 
used for wire bundling and making harnesses. There are many choices of lacing cord available from Digikey www.digikey.com
We use part number 802534B BK032-ND

Now you can close up the locomotive and reinstall the coupler assemblies. Be sure to be mindful of wire routing and reassembly of the shell as to not damage 
or foul the installation. Your Walthers EMD SD45 is now WOWSound equipped and ready to roll!


Other solder tips: When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire


Like us on Facebook Subscribe to our YouTube Channel Join our newsletter
  Back To Top
Home
Entire contents © Copyright Train Control Systems 2004-2017