This installation is for a HO-Scale Life Like Proto 2000 SD7 using a TCS WOW121-Diesel Decoder, AK-MB1 Motherboard with built in Keep Alive™
and UNIV-SH1-C WOWSpeaker kit.

This was performed by our friends from DCC Xpress installations.
They offer high quality WOWSound installations for a flat rate complete with free return shipping!
You can find them at: www.dxinstalls.com

This was performed by our friends from DCC Xpress installations.
They offer high quality WOWSound installations for a flat rate complete with free return shipping!
You can find them at: www.dxinstalls.com


These items are available in the WDK-KAT-1 which was used for this installation.
GEN-MB1 Motherboard with Keep Alive™ WOW121-Diesel Decoder UNIV-SH1-C Speaker Kit
Click here for more information on the WDK-KAT-1 and the rest of the WOWDiesel Kits line.

Important Soldering Tip:
Please do not use any flux either liquid or paste on the mother board. It will damage it. Use only Rosin core solder approved for electronics use.
We recommend to use only Kester "44" rosin core, SN63PB37, .015" diameter, part number 24-6337-0007.
This can be ordered from Techni-Tool under Techni-Tool part number 488SO157

http://www.techni-tool.com

HO-Scale Life Like Proto 2000 SD7 shown prior to installation.

 To start off this install, we must first remove the front and rear coupler screws and their housings.
With the couplers removed, while gently pulling outwards at each end and along each side of the frame, lift the shell off of the frame.
Take care to release the handrails as you lift off the shell so they don't break.

Shown with the shell off.

To remove the original lighting board, Remove the four screws as highlighted above in red and remove the board.

After the board is removed, carefully remove the two rear and single front mounting posts as highlighted above.
In this installation, we also removed and discard the original 1.5 V bulbs and replaced them with LEDs inserted into the original locations.

TCS motherboards include on board current limit resistors for LED use. There is no need to apply external resistors for LED use. 


Using double sided foam tape, attach the AK-MB1 to the frame as shown above. Likewise, with the same tape, with the 35mm X 16mm WOWSound speaker
inserted into the UNIV-SH1-C enclosure, mount this assembly the rear of the frame.

If your speaker enclosure installation covers the portholes on the enclosure, we recommend adding new port hole(s) similar to the original porting. Be sure that the new portholes are the same size and amount of the original and are vented freely into the locomotive We have found introducing a port of the correct size greatly increases the volume and sound quality of the installation. Too much or too little porting decreases the sound quality.

Solder the motor, track, lighting and speaker leads to the AK-MB1 according to the included wiring diagram.

You can now plug in your WOW121 decoder.

Lastly, in order to keep the wires neat and prevent possible shorts, lace the wires into a bundle using lacing cord, which is a wax impregnated string 
used for wire bundling and making harnesses. There are many choices of lacing cord available from Digikey www.digikey.com
We use part number 802534B BK032-ND

Now you can close up the locomotive and reinstall the coupler assemblies. Be sure to be mindful of wire routing and reassembly of the shell as to not damage 
or foul the installation. Your Life Like Proto 2000 SD7 is now WOWSound equipped and ready to roll!


Other solder tips: When stripping wire, only strip a tiny little bit of the insulation. Strip no more then a 1/64 of an inch. When the wire gets tinned with solder the insulation will shrink back more. Try to not expose any more wire then half the length of the solder pad at most. In no case should solder or exposed wire wire ever be outside the boundary of the the solder pad you are attaching a wire to.
Click here for important information on properly Stripping and Tinning wire

Like us on Facebook Subscribe to our YouTube Channel Join our newsletter
  Back To Top
Home
Entire contents © Copyright Train Control Systems 2004-2017